Basic Router CLI Show Command

General Use
No. Perintah Penuh Perintah Singkat Maksud Perintah
1 Show running-config ( Sh run ) Mengetahui konfigurasi yang aktif didalam DRAM (dynamic random acces memory)

2 Show startup-config ( Sh start ) Mengetahui konfigurasi yang sudah tersimpan didalam NVRAM

3 Show version ( Sh ver ) Menampilkan informasi tentang versi software yang sedang berjalan lengkap dengan informasi hardware dan device


Routing Related

No. Perintah Penuh Perintah Singkat Maksud Perintah
1 Show ip protocols ( Sh ip prot ) Untuk menampilkan ip protokol

2 Show ip route ( Sh ip rout ) Menampilkan konfigurasi routing


Interface Related

No. Perintah Penuh Perintah Singkat Maksud Perintah
1 Show interfaces ( Sh int ) Untuk menampilkan statistic semua interfaces router

2 Shoe ip interfaces brief ( Sh ip int bri) Memerinsa status atau kondisi dari tiap-tiap interface yang telah dikonfigurasi

3 Show protocols ( Sh prot ) Menampilkan status interface baik secara global maupun khusus dari protocol layer 3 yang terkonfigurasi


Connectivity Related

No. Perintah Penuh Perintah Singkat Maksud Perintah
1 Show cdp neightbors ( Sh cdp neig ) Menunjukan tentang informasi semua piranti cisco tetangga yaitu switch dan router

2 Show session ( Sh sess ) Memperlihatkan sesi yang ada sekarang

3 Show ssh ( Show ssh ) Untuk melihat koneksi ssh

4 Ping ( Ping ) Mengecek koneksi

5 Traceroute ( Tr ) Untuk menentukan jalur terbaik

Konfigurasi pada Router 1

--- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no


Press RETURN to get started!
Router>ena
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.1.1 255.255.255.0
Router(config-if)#no shut
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit

Router(config)#int se2/0
Router(config-if)#ip add 192.168.2.1 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#no shut
%LINK-5-CHANGED: Interface Serial2/0, changed state to up
Router(config-if)#exit
Router(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up


Router(config)#router rip
Router(config-router)#version 2
Router(config-router)#network 192.168.1.0
Router(config-router)#network 192.168.2.0
Router(config-router)#exit
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console


Konfigurasi pada router 2

--- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no


Press RETURN to get started!

Router>ena
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.3.1 255.255.255.0
Router(config-if)#no shut
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit

Router(config)#int se2/0
Router(config-if)#ip add 192.168.2.2 255.255.255.0
Router(config-if)#no shut
%LINK-5-CHANGED: Interface Serial2/0, changed state to up
Router(config-if)#exit

Router(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up
Router(config)#router rip
Router(config-router)#version 2
Router(config-router)#network 192.168.2.0
Router(config-router)#network 192.168.3.0
Router(config-router)#exit
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console



setting ip Pc 1

ip : 192.168.1.2
sm : 255.255.255.0
dg : 192.168.1.1


setting ip Pc 2

ip : 192.168.3.2
sm : 255.255.255.0
dg : 192.168.3.1